HEYLOVE. Tint base, VERY PERI, 15 ml, tint base
Thanks to dense pigmentation and elasticity, the tinted base VERY PERI creates a perfectly even coating after just one layer. It densely camouflages the free edge and contours.
Shade: purple
Collection: SWEETY
Consistency: medium
Stiffness/Elasticity: elastic
Acidity: neutral, pH=6.7
Smell: neutral
Pigmentation: dense, covers the free edge
How to use:
-
Thoroughly degrease the nail plate with the dehydrator phBond.
- Apply an acid-free primer Ultrabond to the nail tip and wait for the liquid to dry completely.
-
Apply a layer of clear base Rubber base as an undercoat and cure for 30 seconds.
-
Apply one or two layers of Tint base. Cure in a UV/LED lamp for 60 seconds.
-
As the last layer, apply finish coat (top).
Volume: 15 ml
Manufacturer: TM "HEYLOVE"
Country: Ukraine
Ingredients (INCI): Polyacrylic Acid, HEMA, Hydroxycyclohexyl Phenyl Ketone, Ethyl Trimethylbenzoyl Phenylphosphinate, Silica. May Contain: Cl 45380, Cl 15850, Cl 77491, CI 15985, CI 77492, Cl 77007, Cl 77510, CI 77742, CI 77289, CI 77499, CI 77891, CI 7700
Warning! To avoid unwanted polymerization of the material during work, testing, or content shooting, keep the open bottle or brush as far as possible from daylight (especially from direct sunlight). Also, please note that even in cloudy weather, clouds transmit a large amount of ultraviolet radiation, which is sufficient for the material to start polymerizing. When painting tips, we recommend keeping the working side of the UV lamp away from the master. If you hold the switched-on lamp light towards the master, unwanted polymerization of the material on the brushes and necks of open bottles may occur.
Note: all documents are in the attached files!
How to prevent bubbles in the material?Bubbles can appear in any liquid. It does not depend on the formula or components. It depends on the density (viscosity).
It's just a law of physics, nothing else.
For example, in water, bubbles last very briefly and come out on their own.
If we take thicker liquids (honey, thick builder gel, etc.) - bubbles willingly settle in these products and do not leave them as quickly as water.
So with the base. If you work carelessly with the brush, sharply dipping it into the bottle, involuntarily it acts as a blender that mixes the material with air, forming bubbles. This especially applies to materials in bottles with a brush.
Therefore, make GENTLE, gentle movements with the brush!
Especially when the bottle is new and full.
When we were developing the tint base product, we had a choice of thickness. We consciously chose a medium-thick consistency because of its advantages:
- the material doesn't run anywhere, doesn't flood;
- contours are clear without extra effort;
- the master can calmly lay out the architecture and has time to check it by the glare;
- no need to apply a second layer to refine the architecture or camouflage the free edge.
Our production has equipment that prevents the formation of bubbles in the material at all stages – from mixing the pigment to bottling.
We also warn our partners that we are against a store consultant opening a bottle for a client and showing the material. Because a consultant who is not a master does not understand that bubbles can be made with a brush without even realizing it.
Not to mention that the necks of bottles look unsightly when they are contaminated with material up to the top.
If bubbles appear in the material, how to fix it?
Unscrew the cap of the bottle, but do not pull out the brush.
Put it in a warm (but not hot!) place overnight.
Or put the bottle in a plastic bag and immerse it in warm water (up to the shoulders).
According to the law of physics, in a warm environment, molecules move faster, and this speeds up the process.
Air will come to the surface, it is lighter than liquid.
- Ukraine
- Opaque
- Фиолетовые/сиреневые