You Are Cute. Builder Gel #07, 15 ml, builder gel

Builder Gel  is a polymeric light-curing material that, due to its strength, allows for significant lengthening of the nail plate. It contains photoinitiators that trigger the polymerization process when the material is exposed to ultraviolet light of a specific wavelength.

Features:

• It is acid-free.
• Has shock absorption, does not crack upon impact.
• Has a medium consistency.
• Has medium pigmentation, covers the free edge.
• Suitable for the “sculpting without filing” technique.
• Suitable for sculpting on “upper forms”.
• Does not cause a burning sensation in the lamp.
• Becomes thicker in the cold and thinner in warmth.
• Thixotropic — becomes thinner if the brush is moved during work.
• It can be additionally warmed to make the gel thinner.
• Hard at a thickness of 1 mm. If the thickness is less than 1 mm, it may bend slightly, but this does not affect wear.
• Does not shrink and holds the arch well.
• Requires a base coat of Rubber Base.
• Wavelength for polymerization 365-405 nm.
• UV/LED lamp power 36-48W.
• Allowable coating thickness 0.5 mm at the tip / 1 mm at the apex.
• Full polymerization 120 seconds.

Application Method: 

STRENGTHENING

1. Removal.
2. Do not file the nail shape or leave 2 mm in length, which we will remove after leveling.
3. Using a 220-grit nail file, file the top of the nail without heavy pressure, lifting the scales of the nail plate, or use a 100-grit buffer.
4. Do a manicure.
5. If working with removers, wash hands with soap after using them.
6. Degrease the nail with Nail Prep. Do two rounds. Use 4 wipes for this (1 wipe for 5 fingers). First round: wipe the nail surface. Second round: take an orange stick, wrap a wipe around it, and wipe everything in the cuticle area and sidewalls.
7. Use primer optionally, but if the base for the underlayment has sufficient acidity, it is not needed.
8. The underlayment with Rubber Base is best applied with a flat gel brush. Movements should be rubbing. Paint all the nail grooves and cure in the lamp for 60 seconds.
9. Wipe off the sticky layer.
10. Level the nail. If leveling with gel, leave a 0.5-1 mm gap from the cuticle. Cure in the lamp for 60 seconds.
11. File the shape after leveling. This is necessary to create thickness at the nail edge that will support the free edge.
12. If the nail was thin, it may curl, so be sure to file off 1 mm of the natural nail from the inside. In this case, there will be no material lifting. If the material is hard and the nail is very soft, the natural nail will start separating from the hard material at the free edge.
13. After filing, wipe off the sticky layer and apply gel polish.
14. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

CLASSIC EXTENSION

1. Removal
2. Shorten the nail length to 1 mm and make a round shape.
3. Using a 220-grit nail file, file the top of the nail without heavy pressure, lifting the scales of the nail plate, or use a 100-grit buffer.
4. Do a manicure.
5. If working with removers, wash hands with soap after using them.
6. Degrease the nail with Nail Prep. Do two rounds. Use 4 wipes for this (1 wipe for 5 fingers). First round: wipe the nail surface. Second round: take an orange stick, wrap a wipe around it, and wipe everything in the cuticle area and sidewalls.
7. Use a primer
8. The underlayment with Rubber Base is best applied with a flat gel brush. Movements should be rubbing. Paint all the nail grooves and cure in the lamp for 60 seconds.
9. Wipe off the sticky layer.
10. Place a nail form for extending the free edge.
11. Sculpt the artificial nail shape with clear gel. Cure for 30 seconds.
12. File the free edge and shape the nail as desired.
13. Wipe off the sticky layer and excess dust.
14. Go over again with Rubber Base on the areas where the nail file was used. Cure for 30 seconds.
15. Level with gel, place in the lamp and pinch at the 10-15th second. If the gel has strong stickiness or contains glitter, pinch at the 20th second.
16. Finish curing in the lamp for 120 seconds.
17. Wipe off the sticky layer before applying gel polish.
18. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

(Product photos on the website may differ from the actual product)

TPO FREE