HEYLOVE. Flow base, TRUE, 15 ml, colored base of medium-thin consistency

Thanks to dense pigmentation and elasticity, the TRUE tinted base creates a perfectly even coating right after the first layer.

Shade: pink-beige

Collection: EVERYDAY

Collection overview at the link: https://www.instagram.com/p/DE4x8s7ICUB/

Consistency: medium, close to low viscosity

Hardness/elasticity: elastic

Acidity: neutral, pH=6.5

Odor: neutral

Pigmentation: dense, covers the free edge

How to use:

• Thoroughly degrease the nail plate with phBond dehydrator.
• Apply Ultrabond acid-free primer to the nail tip and wait for the liquid to fully dry.
• Apply a layer of Rubber base clear base as an underlay and cure for 30 seconds.
• Apply one or two coats of Flow base. Cure in UV/LED lamp for 60 seconds.
• As the last layer, apply a finish coating (top).

Volume: 15 ml

Manufacturer: TM "HEYLOVE"

Country: Ukraine

Ingredients (INCI): Polyacrylic Acid, HEMA, Hydroxycyclohexyl Phenyl Ketone, Ethyl Trimethylbenzoyl Phenyiphosphinate, Silica. May Contain: Cl 45380, Cl 15850, Cl 77491, Cl 15985, CI 77492, Cl 77007, CI 77510, Cl 77742, Cl 77289, CI 77499, CI 77891, Cl 7700

Attention! To avoid unwanted polymerization of the material during work, testing, or content shooting, the open bottle or brush should be kept as far as possible from daylight (especially direct sunlight). Please also note that even on cloudy days, clouds transmit a large amount of ultraviolet radiation, which is sufficient for the material to start polymerizing. When painting nail tips, we recommend keeping the working side of the UV lamp pointing away from the technician. If the lamp is on and facing the technician, unwanted polymerization of the material on brushes and necks of open bottles may occur.

Note: all documents are in the attached files!

How to prevent bubbles in the material?

Bubbles can appear in any liquid. This does not depend on the formula or ingredients. It depends on density (viscosity).
It's simply a law of physics, nothing else.

For example, bubbles in water are very short-lived and escape on their own.
If we take thicker liquids (honey, thick builder gel for extensions, etc.) - bubbles readily settle in these products and do not leave them as quickly as water.

So with a base. If you work carelessly with the brush, plunging it sharply into the bottle, it inadvertently acts as a blender that mixes the material with air, creating bubbles. This is especially true for materials in bottles with a brush.

Therefore, make CAREFUL, gentle movements with the brush!
Especially when the bottle is new and full.

When we were developing the tint base product, we made a choice about consistency. We deliberately chose a medium-thick consistency because it has advantages:
- the material does not run or flood;
- contours are sharp without extra effort;
- the technician calmly lays down the architecture and has time to check it by reflection;
- there is no need to apply a second layer to refine the architecture or to camouflage the free edge.

At our production, we have equipment that prevents bubble formation in the material at all stages – from mixing the pigment to filling into bottles.

We also warn our partners that we are against a store consultant opening a bottle for a client and showing the material. Because a consultant who is not a master does not realize that bubbles can be created with the brush, even unknowingly.
Not to mention that bottle necks look unsightly when they are soiled with material to the very top.

If bubbles have appeared in the material, how to fix it?

Unscrew the bottle cap, but do not pull out the brush.
Place in a warm (but not hot!) place overnight.
Or put the bottle in a plastic bag and immerse in warm water (up to the shoulders).

According to the law of physics, in a warm environment, molecules move faster, and this speeds up the process.
Air will rise to the surface, as it is lighter than liquid.