You Are Cute. Builder Gel #23, 15 ml, builder gel for extensions with white flowers and colored particles

Builder Gel  is a polymer light-curing material that, due to its strength, allows significant lengthening of the nail plate. It contains photoinitiators that start the polymerization process when the material is exposed to ultraviolet light of a certain wavelength.

Features:

• Is acid-free.
• Has shock absorption, does not crack upon impact.
• Has a medium consistency.
• Has medium pigmentation, covers the free edge.
• Suitable for the 'no-file extension' technique.
• Suitable for extension on 'upper forms'.
• Does not cause a burning sensation in the lamp.
• Becomes thicker in the cold and thinner in the warmth.
• Thixotropic — becomes thinner if you move the brush during work.
• It can be additionally warmed up to make the gel thinner.
• Hard at a thickness of 1 mm. If the thickness is less than 1 mm, it may bend slightly, but this does not affect wear.
• Does not shrink and holds the arch well.
• Requires a base layer of Rubber Base.
• Wavelength for polymerization: 365-405 nm.
• UV/LED lamp power: 36-48W.
• Allowable coating thickness: 0.5 mm at the tip / 1 mm at the apex.
• Full polymerization: 120 seconds.

Application method:

STRENGTHENING

1. Removal.
2. Do not file the nail shape or leave 2 mm in length, which we will remove after leveling.
3. With a 220-grit nail file, file without strong pressure on the nail from above, lifting the scales of the nail plate, or use a 100-grit buffer.
4. Perform a manicure.
5. If working with removers, wash hands with soap after using them.
6. Degrease the nail with Nail Prep. Do two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, place a wipe on it, and wipe everything in the cuticle area and sidewalls.
7. Primer is used optionally, but if the base for the underlay has sufficient acidity, it is not needed.
8. The underlay with Rubber Base is best applied with a flat gel brush. Movements should be rubbing. Paint all the nail sidewalls and cure in the lamp for 60 seconds.
9. Wipe off the sticky layer.
10. Level. If leveling with gel, leave a 0.5–1 mm gap from the cuticle. Cure in the lamp for 60 seconds.
11. File the shape after leveling. This is necessary to create thickness at the nail edge that will hold the free edge.
12. If the nail was thin, it may curl, so be sure to file out 1 mm of the natural nail from the inside. In this case, there will be no material lifting. If the material is hard and the nail is very soft, the nail itself will start to separate from the hard material from the free edge.
13. After filing, wipe off the sticky layer and apply gel polish.
14. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

CLASSIC EXTENSION

1. Removal
2. Shorten the nail length to 1 mm and create a round shape.
3. With a 220-grit nail file, file without strong pressure on the nail from above, lifting the scales of the nail plate, or use a 100-grit buffer.
4. Perform a manicure.
5. If working with removers, wash hands with soap after using them.
6. Degrease the nail with Nail Prep. Do two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, place a wipe on it, and wipe everything in the cuticle area and sidewalls.
7. Use primer
8. The underlay with Rubber Base is best applied with a flat gel brush. Movements should be rubbing. Paint all the nail sidewalls and cure in the lamp for 60 seconds.
9. Wipe off the sticky layer.
10. Place the form for extending the free edge of the nail.
11. Sculpt the artificial nail shape with clear gel. Cure for 30 seconds.
12. File the free edge and shape the nail as desired.
13. Wipe off the sticky layer and excess dust.
14. Go over again with Rubber Base on the areas where the file was used. Cure for 30 seconds.
15. Level with gel, place in the lamp, and pinch at the 10–15 second mark. If the gel has strong stickiness or contains glitter, pinch at the 20 second mark.
16. Finish curing in the lamp for 120 seconds.
17. Wipe off the sticky layer before applying gel polish.
18. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

(Product photos on the website may differ from the actual product)

TPO FREE