You Are Cute. Builder Gel #09, 15 ml, builder gel

Builder Gel – a polymer light-curing material that, due to its strength, allows significant extension of the nail plate. It contains photoinitiators that trigger the polymerization process when the material is exposed to ultraviolet light of a certain wavelength.

Features:

• It is acid-free.
• It has shock absorption, does not crack upon impact.
• It has a medium consistency.
• It has medium pigmentation, covers the free edge.
• Suitable for the "non-file extension" technique.
• Suitable for "upper form" extensions.
• Does not cause a burning sensation in the lamp.
• Becomes thicker in the cold and thinner in warmth.
• Thixotropic — becomes thinner when the brush is moved during application.
• It can be additionally warmed up to make the gel thinner.
• Hard at a thickness of 1 mm. If the thickness is less than 1 mm, it may bend slightly, but this does not affect wear.
• Does not shrink and holds the arch well.
• Requires a base coat of Rubber Base.
• Wavelength for polymerization: 365-405 nm.
• UV/LED lamp power: 36-48W.
• Allowable coating thickness: 0.5 mm at the tip / 1 mm at the apex.
• Full polymerization: 120 seconds.

Application method: 

REINFORCEMENT

1. Removal.
2. Do not file the nail shape, or leave 2 mm of length to be removed after leveling.
3. Using a 220 grit nail file, lightly file the top of the nail without heavy pressure, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Perform a manicure.
5. If working with removers, wash hands with soap after use.
6. Degrease the nail with Nail Prep. Do two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, wrap a wipe around it, and wipe thoroughly in the cuticle area and sidewalls.
7. Use a primer optionally, but if the base coat has sufficient acidity, it is not needed.
8. Apply the Rubber Base undercoat with a flat gel brush. Movements should be rubbing. Paint all the nail sidewalls and cure in the lamp for 60 seconds.
9. Wipe off the sticky layer.
10. Level. If leveling with builder gel, keep a 0.5–1 mm distance from the cuticle. Cure in the lamp for 60 seconds.
11. File the shape after leveling. This is necessary to create thickness at the nail edge to support the free edge.
12. If the nail was thin, it may curl, so be sure to file away 1 mm of the natural nail from the inside. This will prevent material lifting. If the material is hard and the nail is very soft, the nail itself will start to separate from the hard material at the free edge.
13. After filing, wipe off the sticky layer and apply gel polish.
14. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

CLASSIC EXTENSION

1. Removal
2. Shorten the nail length to 1 mm and create a round shape.
3. Using a 220 grit nail file, lightly file the top of the nail without heavy pressure, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Perform a manicure.
5. If working with removers, wash hands with soap after use.
6. Degrease the nail with Nail Prep. Do two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, wrap a wipe around it, and wipe thoroughly in the cuticle area and sidewalls.
7. Use a primer
8. Apply the Rubber Base undercoat with a flat gel brush. Movements should be rubbing. Paint all the nail sidewalls and cure in the lamp for 60 seconds.
9. Wipe off the sticky layer.
10. Place the nail form for extending the free edge.
11. Apply clear builder gel to sculpt the artificial nail. Cure for 30 seconds.
12. File the free edge and shape the nail as desired.
13. Wipe off the sticky layer and excess dust.
14. Go over the areas where the file was used with Rubber Base again. Cure for 30 seconds.
15. Level with builder gel, place in the lamp, and pinch at 10–15 seconds. If the gel has strong adhesion or contains glitter, pinch at 20 seconds.
16. Finish curing in the lamp for 120 seconds.
17. Wipe off the sticky layer before applying gel polish.
18. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

(Product photos on the website may differ from the actual product)

TPO FREE