You Are Cute. Builder Gel #37, 15 ml, builder gel with glitter particles

Builder Gel – a polymer light-curing material that, due to its strength, allows you to significantly lengthen the nail plate. It contains photoinitiators that start the polymerization process when the material is exposed to ultraviolet light of a specific wavelength.

Features:

• Is acid-free.
• Has shock absorption, does not crack on impact.
• Has a medium consistency.
• Has medium pigmentation, covers the free edge.
• Suitable for the "no-filing extension" technique.
• Suitable for extension "on top forms".
• Does not cause burning in the lamp.
• Becomes thicker in cold, thinner in heat.
• Thixotropic — becomes thinner if you move the brush during work.
• It can be additionally heated to make the gel thinner.
• Hard at 1 mm thickness. If thickness is less than 1 mm, it may bend slightly, but this does not affect wear.
• Does not shrink and holds the arch well.
• Mandatorily requires an undercoat of Rubber Base.
• Wavelength for polymerization 365-405 nm.
• UV/LED lamp power 36-48W.
• Allowed coating thickness 0.5 mm at the free edge / 1 mm at the apex.
• Full polymerization 120 seconds.

Application method:

STRENGTHENING

1. Removal.
2. Do not file the nail shape or leave 2 mm length, which will be removed after leveling.
3. With a 220 grit nail file, file without strong pressure on the nail from above, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Do a manicure.
5. If working with removers, wash hands with soap after working with them.
6. Degrease the nail with Nail Prep. Do two approaches. Use 4 wipes (1 wipe per 5 fingers). First approach: wipe the nail surface. Second approach: take an orange stick, put a wipe on it and wipe everything in the cuticle area and in the sinuses.
7. Use primer optionally, but if the base for undercoat has sufficient acidity, it is not needed.
8. It is best to apply the Rubber Base undercoat with a flat gel brush. Movements should be rubbing. Draw all nail sinuses and cure in lamp for 60 seconds.
9. Wipe off the sticky layer.
10. Level. If leveling with gel, make an indentation from the cuticle 0.5–1 mm. Cure in lamp for 60 seconds.
11. File the shape after leveling. This is necessary so that a thickness forms at the edge of the nail that will hold the free edge.
12. If the nail was thin, it may curl, so be sure to file 1 mm of the natural nail from the inside. In this case, there will be no material chipping. If the material is hard and the nail is very soft, the nail itself will begin to separate from the hard material from the free edge.
13. After filing, wipe off the sticky layer and cover with gel polish.
14. Cover with top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

CLASSIC EXTENSION

1. Removal.
2. Shorten the nail length to 1 mm and make a round shape.
3. With a 220 grit nail file, file without strong pressure on the nail from above, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Do a manicure.
5. If working with removers, wash hands with soap after working with them.
6. Degrease the nail with Nail Prep. Do two approaches. Use 4 wipes (1 wipe per 5 fingers). First approach: wipe the nail surface. Second approach: take an orange stick, put a wipe on it and wipe everything in the cuticle area and in the sinuses.
7. Use primer.
8. It is best to apply the Rubber Base undercoat with a flat gel brush. Movements should be rubbing. Draw all nail sinuses and cure in lamp for 60 seconds.
9. Wipe off the sticky layer.
10. Set the form for extending the free edge of the nail.
11. Lay out the shape of the artificial nail with transparent gel. Cure for 30 seconds.
12. File the free edge and give the nail the desired shape.
13. Wipe off the sticky layer and excess dust.
14. Go over the areas where the file was used again with Rubber Base. Cure for 30 seconds.
15. Level with gel, put in lamp and press at 10–15 seconds. If the gel has strong stickiness or contains glitter, press at 20 seconds.
16. Cure further in lamp for 120 seconds.
17. Wipe off the sticky layer before covering with gel polish.
18. Cover with top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

(Product photos on the site may differ from the actual product)

TPO FREE