Cart is empty
HEYLOVE. Tint base, GUMMY, 15 ml, tinted base
Please sign in so that we can notify you about a reply
Thanks to the dense pigmentation and elasticity, the tinted base GUMMY creates a perfectly even coating after the first layer.
Shade: Barbie pink
Collection: JUICY
Consistency: medium
Hardness/elasticity: elastic
Acidity: neutral, pH=6.7
Odor: neutral
Pigmentation: dense, covers the free edge
Application method:
-
Thoroughly degrease the nail plate using the dehydrator phBond.
- Apply acid-free primer Ultrabond to the nail tip and wait until the liquid is completely dry.
-
Apply a layer of clear base Rubber base as a substrate and cure for 30 seconds.
-
Apply one or two layers of Tint base. Cure in UV/LED lamp for 60 seconds.
-
As the final layer, apply finish coating (top).
Volume: 15 ml
Manufacturer: TM "HEYLOVE"
Country: Ukraine
INCI ingredients: Polyacrylic Acid, HEMA, Hydroxycyclohexyl Phenyl Ketone, Ethyl Trimethylbenzoyl Phenylphosphinate, Silica. May Contain: Cl 45380, Cl 15850, Cl 77491, CI 15985, CI 77492, Cl 77007, Cl 77510, CI 77742, CI 77289, CI 77499, CI 77891, CI 7700
Warning! To avoid unwanted polymerization of the material during work, testing, or content shooting, keep the opened bottle or brush as far away from daylight as possible (especially direct sunlight). Please also note that even in cloudy weather, clouds transmit a large amount of ultraviolet radiation, which is sufficient for the material to start polymerizing. When painting nail tips, we recommend keeping the working side of the UV lamp that is on, facing away from the technician. If you hold the switched-on lamp with the light towards the technician, unwanted polymerization of the material on brushes and on the necks of opened bottles may occur.
Note: all documents are in the attached files!
How to prevent bubbles in the material?Bubbles can appear in any liquid. It does not depend on the formula or ingredients. It depends on density (viscosity).
It's just a law of physics, nothing else.
For example, in water, bubbles last for a very short time and come out on their own.
If we take thicker liquids (honey, thick builder gel for extensions, etc.) - in these products, bubbles readily settle in and do not leave them as quickly as water.
So it is with the base. If you work carelessly with the brush, sharply dipping it into the bottle, it involuntarily acts as a blender, mixing the material with air, forming bubbles. This especially applies to materials in bottles with a brush.
So make CAREFUL, gentle movements with the brush!
Especially when the bottle is new and full.
When we were working on the development of the tint base product, we had a choice of density. We consciously chose a medium-thick consistency because it has advantages:
- the material does not run anywhere, does not flood the sidewalls;
- the contours are clear without extra effort;
- the technician calmly lays out the architecture and has time to check it by the gloss;
- there is no need to apply a second coat to refine the architecture or camouflage the free edge.
At our production, we have equipment that prevents the formation of bubbles in the material at all stages - from mixing the pigment to pouring into bottles.
We also warn our partners that we are against a store consultant opening a bottle for a client and showing the material. Because a consultant who is not a technician does not understand that bubbles can be created with the brush, even without realizing it.
Not to mention that the bottle necks look unsightly when the material has been contaminated up to the very top.
If bubbles appear in the material, how to fix it?
Unscrew the bottle cap, but do not pull out the brush.
Put in a warm (but not hot!) place overnight.
Or put the bottle in a plastic bag and immerse in warm water (up to the shoulders).
According to the law of physics, in a warm environment, molecules move faster, and this speeds up the process.
The air will come to the surface, it is lighter than the liquid.