You Are Cute. Builder Gel #27, 15 ml, builder gel for extensions with colorful hearts

Builder Gel – a polymer light-curing material that, due to its strength, allows significant lengthening of the nail plate. It contains photoinitiators that start the polymerization process when the material is exposed to ultraviolet light of a certain wavelength.

Features:

• It is acid-free.
• It has shock absorption, does not crack upon impact.
• It has a medium consistency.
• It has medium pigmentation, covers the free edge.
• Suitable for the "sculpting without filing" technique.
• Suitable for sculpting on "top forms".
• Does not cause burning in the lamp.
• Becomes thicker in the cold and thinner in warmth.
• Thixotropic – becomes thinner if you move the brush during work.
• It can be additionally heated to make the gel thinner.
• Hard at a thickness of 1 mm. If the thickness is less than 1 mm, it may slightly bend, but this does not affect wear.
• Does not shrink and holds the arch well.
• Absolutely requires an underlay of Rubber Base.
• Polymerization wavelength 365-405 nm.
• UV/LED lamp power 36-48W.
• Allowable coating thickness 0.5 mm at the tip / 1 mm at the apex.
• Full polymerization 120 seconds.

Application method:

STRENGTHENING

1. Removal.
2. Do not file the nail shape or leave 2 mm in length, which we will remove after alignment.
3. With a 220 grit nail file, file without strong pressure on the top of the nail, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Perform a manicure.
5. If working with removers, wash hands with soap after working with them.
6. Degrease the nail with Nail Prep. Do two approaches. Use 4 wipes (1 wipe per 5 fingers). First approach: wipe the nail surface. Second approach: take an orange stick, put a wipe on it, and wipe everything in the cuticle area and nail folds.
7. Use primer optionally, but if the base for the underlay has sufficient acidity, it is not needed.
8. The underlay with Rubber Base is best applied with a flat gel brush. Movements should be rubbing. Draw in all nail folds and cure in the lamp for 60 seconds.
9. Wipe off the tacky layer.
10. Align. If aligning with gel, make an indent from the cuticle of 0.5–1 mm. Cure in the lamp for 60 seconds.
11. File the shape after aligning. This is needed to create thickness at the nail edge that will hold the free edge.
12. If the nail was thin, it may curl, so be sure to file out 1 mm of the natural nail from the inside. In this case, there will be no material lifting. If the material is hard and the nail is very soft, the nail itself will start to separate from the hard material from the free edge.
13. After filing, wipe off the tacky layer and cover with gel polish.
14. Apply top coat. Cure for 120 seconds. After drying, do not wipe with anything, as shine may be lost.

CLASSIC SCULPTING

1. Removal
2. Reduce nail length to 1 mm and make a round shape.
3. With a 220 grit nail file, file without strong pressure on the top of the nail, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Perform a manicure.
5. If working with removers, wash hands with soap after working with them.
6. Degrease the nail with Nail Prep. Do two approaches. Use 4 wipes (1 wipe per 5 fingers). First approach: wipe the nail surface. Second approach: take an orange stick, put a wipe on it, and wipe everything in the cuticle area and nail folds.
7. Use primer
8. The underlay with Rubber Base is best applied with a flat gel brush. Movements should be rubbing. Draw in all nail folds and cure in the lamp for 60 seconds.
9. Wipe off the tacky layer.
10. Place a sculpting form for the free edge of the nail.
11. Lay out the artificial nail form with clear gel. Cure for 30 seconds.
12. File the free edge and shape the nail as desired.
13. Wipe off the tacky layer and excess dust.
14. Go over the areas where the file was used again with Rubber Base . Cure for 30 seconds.
15. Align with gel, place in the lamp and pinch at the 10–15th second. If the gel has strong tackiness or contains glitter, pinch at the 20th second.
16. Cure additionally in the lamp for 120 seconds.
17. Wipe off the tacky layer before covering with gel polish.
18. Apply top coat. Cure for 120 seconds. After drying, do not wipe with anything, as shine may be lost.

(Photo of the product on the site may differ from the actual product)

TPO FREE