You Are Cute. Builder Gel #28, 15 ml, builder gel with colored hearts

Builder Gel – a polymer light-curing material that, thanks to its strength, allows you to significantly lengthen the nail plate. It contains photoinitiators that initiate the polymerization process when the material is exposed to ultraviolet light of a specific wavelength.

Features:

• Acid-free.
• Has shock absorption, does not crack on impact.
• Medium consistency.
• Medium pigmentation, covers the free edge.
• Suitable for “extension without filing” technique.
• Suitable for extension “on top forms”.
• Does not cause heat spikes in the lamp.
• Becomes thicker in the cold and thinner in warmth.
• Thixotropic – becomes thinner when moving the brush during work.
• It can be additionally warmed up to make the gel thinner.
• Hard at a thickness of 1 mm. If the thickness is less than 1 mm, it may bend slightly, but this does not affect wear.
• Does not shrink and holds the arch well.
• Necessarily requires a base of Rubber Base.
• Polymerization wavelength 365-405 nm.
• UV/Led-lamp power 36-48W.
• Allowable coating thickness 0.5 mm at the tip / 1 mm at the apex.
• Full polymerization 120 seconds.

Application method:

STRENGTHENING

1. Removal.
2. Do not file the nail shape or leave 2 mm in length, which will be removed after leveling.
3. Use a 220 grit nail file to file the nail from above without strong pressure, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Perform a manicure.
5. If working with removers, wash hands with soap after using them.
6. Degrease the nail with Nail Prep. Make two passes. Use 4 wipes (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange wood stick, wrap a wipe around it, and wipe everything in the cuticle area and sidewalls.
7. Primer is optional, but if the base coat has sufficient acidity, it is not necessary.
8. The Rubber Base underlay is best applied with a flat gel brush. The motions should be rubbing. Work into all sidewalls and cure in the lamp for 60 seconds.
9. Remove the sticky layer.
10. Level. If leveling with gel, step back from the cuticle 0.5–1 mm. Cure in the lamp for 60 seconds.
11. File the shape after leveling. This is needed to create thickness at the nail edge that will hold the free edge.
12. If the nail was thin, it may curl, so be sure to file 1 mm of the natural nail from the inside. In this case, there will be no material lifting. If the material is hard and the nail is very soft, the nail itself will start to separate from the hard material from the free edge.
13. After filing, remove the sticky layer and apply gel polish.
14. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as it may lose its shine.

CLASSIC EXTENSION

1. Removal
2. Shorten the nail to 1 mm and make a round shape.
3. Use a 220 grit nail file to file the nail from above without strong pressure, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Perform a manicure.
5. If working with removers, wash hands with soap after using them.
6. Degrease the nail with Nail Prep. Make two passes. Use 4 wipes (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange wood stick, wrap a wipe around it, and wipe everything in the cuticle area and sidewalls.
7. Use a primer
8. The Rubber Base underlay is best applied with a flat gel brush. The motions should be rubbing. Work into all sidewalls and cure in the lamp for 60 seconds.
9. Remove the sticky layer.
10. Place the form for extending the free edge of the nail.
11. Apply clear gel to create the artificial nail shape. Cure for 30 seconds.
12. File the free edge and shape the nail as desired.
13. Remove the sticky layer and excess dust.
14. Go over once more with Rubber Base on the areas where the file was used. Cure for 30 seconds.
15. Level with gel, place in the lamp and pinch at the 10–15th second. If the gel has strong stickiness or contains glitter, pinch at the 20th second.
16. Cure in the lamp for 120 seconds.
17. Remove the sticky layer before applying gel polish.
18. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as it may lose its shine.

(Product photos on the website may differ from the actual product)

TPO FREE