You Are Cute. Builder Gel #21, 15 ml, builder gel for extensions with white flowers and colored particles

Builder Gel – a polymer light-curing material that, due to its strength, allows significant extension of the nail plate. It contains photoinitiators that start the polymerization process when the material is exposed to ultraviolet light of a certain wavelength.

Features:

• It is acid-free.
• Has cushioning, does not crack upon impact.
• Has a medium consistency.
• Has medium pigmentation, covers the free edge.
• Suitable for the "non-file extension" technique.
• Suitable for "upper forms" extension.
• Does not cause burning in the lamp.
• Becomes thicker in the cold and thinner in warmth.
• Thixotropic — becomes thinner when worked with a brush.
• It can be additionally warmed to make the builder gel thinner.
• Hard at 1 mm thickness. If the thickness is less than 1 mm, it may slightly bend, but this does not affect wear.
• Does not shrink and holds the arch well.
• Requires a base layer of Rubber Base.
• Wavelength for polymerization: 365-405 nm.
• UV/LED lamp power: 36-48W.
• Allowable coating thickness: 0.5 mm at the tip / 1 mm at the apex.
• Full polymerization: 120 seconds.

Application method: 

STRENGTHENING

1. Removal.
2. Do not file the nail shape or leave 2 mm of length to remove after leveling.
3. Using a 220 grit nail file, file without strong pressure on the nail from above, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Perform a manicure.
5. If working with removers, wash hands with soap after use.
6. Degrease the nail with Nail Prep. Do two passes. Use 4 wipes for this (1 wipe for 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, place a wipe on it, and wipe everything in the cuticle area and sidewalls.
7. Use primer optionally, but if the base for the underlay has sufficient acidity, it is not needed.
8. Apply the Rubber Base underlay best with a flat gel brush. Movements should be rubbing in. Paint all nail recesses and cure in the lamp for 60 seconds.
9. Remove the sticky layer.
10. Level. If leveling with builder gel, leave a 0.5-1 mm gap from the cuticle. Cure in the lamp for 60 seconds.
11. File the shape after leveling. This is necessary to create thickness at the nail edge that will hold the free edge.
12. If the nail was thin, it may curl, so be sure to file out 1 mm of the natural nail from the inside. In this case, there will be no material delamination. If the material is hard and the nail is very soft, the natural nail will start separating from the hard material from the free edge.
13. After filing, remove the sticky layer and apply gel polish.
14. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

CLASSIC EXTENSION

1. Removal
2. Shorten the nail length to 1 mm and create a round shape.
3. Using a 220 grit nail file, file without strong pressure on the nail from above, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Perform a manicure.
5. If working with removers, wash hands with soap after use.
6. Degrease the nail with Nail Prep. Do two passes. Use 4 wipes for this (1 wipe for 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, place a wipe on it, and wipe everything in the cuticle area and sidewalls.
7. Use primer
8. Apply the Rubber Base underlay best with a flat gel brush. Movements should be rubbing in. Paint all nail recesses and cure in the lamp for 60 seconds.
9. Remove the sticky layer.
10. Place a form for extending the free edge of the nail.
11. Lay the artificial nail form with transparent builder gel. Cure for 30 seconds.
12. File the free edge and shape the nail as desired.
13. Wipe off the sticky layer and excess dust.
14. Go over with Rubber Base again on the areas where the file was used. Cure for 30 seconds.
15. Level with builder gel, place in the lamp and pinch at the 10-15 second mark. If the builder gel has strong stickiness or contains glitter, pinch at the 20 second mark.
16. Finish curing in the lamp for 120 seconds.
17. Remove the sticky layer before applying gel polish.
18. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

(Product photos on the site may differ from the actual product)

TPO FREE