HEYLOVE. Tint base, PLUM, 15 ml, tinted base
Thanks to its dense pigmentation and elasticity, the PLUM tinted base creates a perfectly smooth coating even after the first layer.
Shade: bright plum
Collection: JUICY
Consistency: medium
Hardness/elasticity: elastic
Acidity: neutral, pH=6.7
Odor: neutral
Pigmentation: dense, covers the free edge
Application:
-
Thoroughly degrease the nail plate with a dehydrator phBond.
- Apply an acid-free primer Ultrabond to the nail tip and wait for it to dry completely.
-
Apply a layer of clear base Rubber base as a substrate and polymerize for 30 seconds.
-
Apply one or two layers of Tint base. Curing time in a UV/LED lamp is 60 seconds.
-
As the final layer, apply a finish coating (top).
Volume: 15 ml
Manufacturer: TM "HEYLOVE"
Country: Ukraine
Ingredients (INCI): Polyacrylic Acid, HEMA, Hydroxycyclohexyl Phenyl Ketone, Ethyl Trimethylbenzoyl Phenylphosphinate, Silica. May Contain: Cl 45380, Cl 15850, Cl 77491, CI 15985, CI 77492, Cl 77007, Cl 77510, CI 77742, CI 77289, CI 77499, CI 77891, CI 7700
Attention! To avoid unwanted polymerization of the material during work, testing, or content shooting, keep the open bottle or brush as far away from daylight (especially direct sunlight) as possible. Please also note that even in cloudy weather, clouds transmit a significant amount of ultraviolet radiation sufficient for the material to start polymerizing. When coloring tips, we recommend keeping the working side of the active UV lamp facing away from the master. If the lamp is held with the light facing the master, unwanted polymerization of the material on the brushes and necks of open bottles may occur.
Note: all documents are in the attached files!
How to prevent bubbles in the material?Bubbles can appear in any liquid. This does not depend on the formula or ingredients. It depends on the density (viscosity).
It's simply a law of physics, nothing else.
For example, in water, bubbles last very briefly and escape on their own.
If we take thicker liquids (honey, thick builder gel, etc.), bubbles readily settle in these products and do not leave them as quickly as water.
It's the same with base. If the brush is used carelessly, dipping it sharply into the bottle, it involuntarily acts as a blender, mixing the material with air and creating bubbles. This especially applies to materials in bottles with a brush.
Therefore, make GENTLE, delicate movements with the brush!
Especially when the bottle is new and full.
When we were developing the tint base product, we had a choice of density. We deliberately chose a medium consistency density because it has advantages:
- the material does not run or flow anywhere;
- contours are clear without extra effort;
- the master calmly builds the architecture and has time to check it by the gloss;
- there is no need to apply a second layer to refine the architecture or camouflage the free edge.
At our production facility, we have equipment that prevents the formation of bubbles in the material at all stages – from pigment mixing to bottling.
We also warn our partners that we are against the store consultant opening a bottle for a client to show the material. Because a consultant who is not a master does not understand that the brush can create bubbles without even realizing it.
Not to mention that the necks of the bottles look unaesthetic when they are dirty with material up to the top.
If bubbles appear in the material, how to fix it?
Unscrew the bottle cap, but do not remove the brush.
Leave in a warm (but not hot!) place overnight.
Or put the bottle in a plastic bag and submerge it in warm water (up to the neck).
According to the laws of physics, in a warm environment molecules move faster, and this speeds up the process.
Air will rise to the surface; it is lighter than the liquid.
- Ukraine
- Opaque
- Фиолетовые/сиреневые