Cart is empty
HEYLOVE. Tint base, UK, 15 ml, tint base
Please sign in so that we can notify you about a reply
Thanks to its dense pigmentation and elasticity, the UK tint base creates a perfectly even coating after just the first coat. It densely camouflages the free edge and contours.
Shade: yellow
Collection: SWEETY
Consistency: medium
Hardness/elasticity: elastic
Acidity: neutral, pH=6.7
Odor: neutral
Pigmentation: dense, covers the free edge
Application method:
-
Thoroughly degrease the nail plate using a dehydrator phBond.
- Apply an acid-free primer to the nail tip Ultrabond and wait for the liquid to dry completely.
-
Apply a layer of clear base Rubber base as a substrate and cure for 30 seconds.
-
Apply one or two coats of Tint base. Curing time in a UV/LED lamp is 60 seconds.
-
As the final layer, apply top coat.
Volume: 15 ml
Manufacturer: TM "HEYLOVE"
Country: Ukraine
INCI: Polyacrylic Acid, HEMA, Hydroxycyclohexyl Phenyl Ketone, Ethyl Trimethylbenzoyl Phenylphosphinate, Silica. May Contain: Cl 45380, Cl 15850, Cl 77491, CI 15985, CI 77492, Cl 77007, Cl 77510, CI 77742, CI 77289, CI 77499, CI 77891, CI 7700
Attention! To avoid unwanted polymerization of the material during work, testing, or content shooting, keep the open bottle or brush as far as possible from daylight (especially direct sunlight). Also, please note that even in cloudy weather, clouds transmit a large amount of ultraviolet radiation sufficient for the material to start polymerizing. When painting nail tips, we recommend keeping the working side of the UV lamp facing away from the master. If you keep the lamp on with the light facing the master, unwanted polymerization of the material on brushes and necks of open bottles may occur.
Note: all documents are in the attached files!
How to prevent bubbles in the material?Bubbles can appear in any liquid. It does not depend on the formula or ingredients. It depends on density (viscosity).
It's just a law of physics, nothing else.
For example, in water, bubbles hold very briefly and escape on their own.
If we take thicker liquids (honey, thick builder gel, etc.) - bubbles happily settle in these products and do not leave them as quickly as water.
The same goes for base. If you work carelessly with the brush, sharply dipping it into the bottle, it involuntarily acts as a blender, mixing the material with air and forming bubbles. This is especially true for materials in bottles with a brush.
Therefore, make GENTLE, delicate movements with the brush!
Especially when the bottle is new and full.
When we were developing the tint base product, we had a choice of density. We deliberately chose a medium density consistency because it has advantages:
- The material does not run or bleed anywhere;
- Contours are clear without extra effort;
- The master calmly builds the architecture and has time to check it by the gloss;
- There is no need to apply a second coat to correct the architecture or camouflage the free edge.
Our production facility has equipment that prevents the formation of bubbles in the material at all stages – from pigment mixing to bottling.
We also warn our partners that we are against a store consultant opening a bottle for a client and showing the material. Because a consultant who is not a master does not understand that bubbles can be created with a brush, even without realizing it.
Not to mention that the necks of bottles look unsightly when they are soiled with material all the way up.
If bubbles appear in the material, how to fix it?
Unscrew the bottle cap, but do not remove the brush.
Place in a warm (but not hot!) place overnight.
Or put the bottle in a plastic bag and immerse it in warm water (up to the shoulders).
According to the law of physics, in a warm environment molecules move faster, and this speeds up the process.
The air will come to the surface – it is lighter than the liquid.