You Are Cute. Builder Gel #44, 15 ml, builder gel, pearlescent

Builder Gel – a polymer light-curing material that, due to its strength, allows significant extension of the nail plate. It contains photoinitiators that start the polymerization process when the material is exposed to ultraviolet light of a specific wavelength.

Features:

• Acid-free.
• Has shock absorption, does not crack upon impact.
• Medium consistency.
• Medium pigmentation, covers the free edge.
• Suitable for the "no-file extension" technique.
• Suitable for extension "on top forms".
• Does not cause burning in the lamp.
• Becomes thicker in cold, thinner in warmth.
• Thixotropic – becomes thinner if you move the brush during work.
• Can be additionally heated to make the gel thinner.
• Hard at a thickness of 1 mm. If the thickness is less than 1 mm, it may bend slightly, but this does not affect wear.
• Does not shrink and holds the arch well.
• Requires a Rubber Base underlayer.
• Wavelength for polymerization 365-405 nm.
• UV/LED lamp power 36-48W.
• Allowable coating thickness 0.5 mm at the tip / 1 mm at the apex.
• Full polymerization 120 seconds.

Application method: 

STRENGTHENING

1. Removal.
2. Do not file the nail shape or leave 2 mm in length, which will be removed after leveling.
3. Using a 220 grit nail file, file without strong pressure on the nail from above, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Do a manicure.
5. If working with removers, wash hands with soap after using them.
6. Degrease the nail with Nail Prep. Do two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, put a wipe on it, and wipe everything in the cuticle area and sinuses.
7. Primer is optional, but if the base for the underlayer has sufficient acidity, it is not needed.
8. It is best to apply the Rubber Base underlayer with a flat gel brush. Movements should be rubbing. Paint all nail sinuses and cure in the lamp for 60 seconds.
9. Wipe off the sticky layer.
10. Level. If leveling with gel, leave a 0.5–1 mm gap from the cuticle. Cure in the lamp for 60 seconds.
11. File the shape after leveling. This is necessary to create thickness at the edge of the nail that will hold the free edge.
12. If the nail was thin, it may curl, so be sure to file 1 mm of the natural nail from the inside. This will prevent material lifting. If the material is hard and the nail is very soft, the nail itself will start to separate from the hard material at the free edge.
13. After filing, wipe off the sticky layer and apply gel polish.
14. Apply top coat. Cure for 120 seconds. After curing, do not wipe anything, as the shine may be lost.

CLASSIC EXTENSION

1. Removal
2. Shorten the nail length to 1 mm and make a round shape.
3. Using a 220 grit nail file, file without strong pressure on the nail from above, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Do a manicure.
5. If working with removers, wash hands with soap after using them.
6. Degrease the nail with Nail Prep. Do two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, put a wipe on it, and wipe everything in the cuticle area and sinuses.
7. Use primer
8. It is best to apply the Rubber Base underlayer with a flat gel brush. Movements should be rubbing. Paint all nail sinuses and cure in the lamp for 60 seconds.
9. Wipe off the sticky layer.
10. Install the form for extending the free edge of the nail.
11. Apply the shape of the artificial nail with clear gel. Cure for 30 seconds.
12. File the free edge and give the nail the desired shape.
13. Wipe off the sticky layer and excess dust.
14. Go over the areas where the file was used once more with Rubber Base. Cure for 30 seconds.
15. Level with gel, place in the lamp, and clamp at the 10–15th second. If the gel has a strong sticky layer or contains glitter, clamp at the 20th second.
16. Finish curing in the lamp for 120 seconds.
17. Wipe off the sticky layer before applying gel polish.
18. Apply top coat. Cure for 120 seconds. After curing, do not wipe anything, as the shine may be lost.

(Product photos on the site may differ from the actual product)

TPO FREE