You Are Cute. Builder Gel #29, 15 ml, builder gel with colorful hearts

Builder Gel – a polymer light-curing material that, due to its strength, allows for significant extension of the nail plate. It contains photoinitiators that start the polymerization process when the material is exposed to ultraviolet light of a specific wavelength.

Features:

• Acid-free.
• Has shock absorption, does not crack under impact.
• Has medium consistency.
• Has medium pigmentation, covers the free edge.
• Suitable for the "non-filing extension" technique.
• Suitable for extension on top forms.
• Does not cause a burning sensation in the lamp.
• Becomes thicker in cold and thinner in heat.
• Thixotropic – becomes thinner if you move the brush during work.
• It can be additionally heated to make the gel thinner.
• Hard at a thickness of 1 mm. If the thickness is less than 1 mm, it may bend slightly, but this does not affect wear.
• No shrinkage and holds the arch well.
• Requires an underlay of Rubber Base.
• Wavelength for polymerization 365-405 nm.
• UV/LED lamp power 36-48W.
• Allowed coating thickness 0.5 mm at the edge/ 1 mm at the apex.
• Complete polymerization 120 seconds.

Application method: 

STRENGTHENING

1. Removal.
2. Do not file the nail shape or leave 2 mm in length, which we will remove after leveling.
3. With a 220 grit file, lightly file the nail from above without strong pressure, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Do a manicure.
5. If working with removers, wash hands with soap after working with them.
6. Degrease the nail with Nail Prep. Do two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, put a wipe on it and wipe everything in the cuticle area and grooves.
7. Use primer optionally, but if the base for the underlay has sufficient acidity, it is not needed.
8. Apply the underlay of Rubber Base best with a flat gel brush. Movements should be rubbing. Paint all grooves of the nail and cure in the lamp for 60 seconds.
9. Wipe off the sticky layer.
10. Level. If leveling with gel, leave a 0.5–1 mm gap from the cuticle. Cure in the lamp for 60 seconds.
11. File the shape after leveling. This is needed to create thickness at the edge of the nail that will hold the free edge.
12. If the nail was thin, it may curl, so be sure to file 1 mm of the natural nail from the inside. In this case, there will be no material lifting. If the material is hard and the nail is very soft, the nail itself will begin to separate from the hard material from the free edge.
13. After filing, wipe off the sticky layer and apply gel polish.
14. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

CLASSIC EXTENSION

1. Removal
2. Shorten the nail length to 1 mm and make a round shape.
3. With a 220 grit file, lightly file the nail from above without strong pressure, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Do a manicure.
5. If working with removers, wash hands with soap after working with them.
6. Degrease the nail with Nail Prep. Do two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, put a wipe on it and wipe everything in the cuticle area and grooves.
7. Use primer
8. Apply the underlay of Rubber Base best with a flat gel brush. Movements should be rubbing. Paint all grooves of the nail and cure in the lamp for 60 seconds.
9. Wipe off the sticky layer.
10. Set the form for extending the free edge of the nail.
11. Apply the artificial nail shape with clear gel. Cure for 30 seconds.
12. File the free edge and give the nail the desired shape.
13. Wipe off sticky layer and excess dust.
14. Go over the areas where you used the file once more with Rubber Base. Cure for 30 seconds.
15. Level with gel, place in the lamp and pinch at the 10-15th second. If the gel has a strong sticky layer or contains glitter, pinch at the 20th second.
16. Finish curing in the lamp for 120 seconds.
17. Wipe off the sticky layer before applying gel polish.
18. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

(Product photos on the site may differ from the actual product)

TPO FREE