You Are Cute. Builder Gel #12, 15 ml, builder gel

Builder Gel – a polymer light-curing material that, due to its strength, allows you to significantly lengthen the nail plate. It contains photoinitiators that start the polymerization process when the material is exposed to ultraviolet light of a certain wavelength.

Features:

• Is acid-free.
• Has cushioning, does not crack upon impact.
• Has a medium consistency.
• Has medium pigmentation, covers the free edge.
• Suitable for the "extension without filing" technique.
• Suitable for extension "on upper forms".
• Does not cause burning in the lamp.
• Becomes thicker in the cold and thinner in the heat.
• Thixotropic — becomes thinner if you move the brush while working.
• It can be additionally heated to make the gel thinner.
• Hard at a thickness of 1 mm. If the thickness is less than 1 mm, it may flex slightly, but this does not affect wear.
• Does not shrink and holds the arch well.
• Requires a Rubber Base underlayer.
• Polymerization wavelength 365-405 nm.
• UV/LED lamp power 36-48W.
• Permissible coating thickness 0.5 mm at the tip/ 1 mm at the apex.
• Full polymerization 120 seconds.

Application method: 

STRENGTHENING

1. Removal.
2. Do not file the nail shape or leave 2 mm in length, which we will remove after leveling.
3. With a 220 grit nail file, file without strong pressure on the nail from above, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Do a manicure.
5. If working with removers, after working with them wash hands with soap.
6. Degrease the nail using Nail Prep. Do two approaches. Use 4 wipes (1 wipe per 5 fingers). First approach: wipe the surface of the nail. Second approach: take an orange stick, put a wipe on it and wipe everything in the cuticle area and sinuses.
7. Use primer optionally, but if the base for the underlayer has sufficient acidity, it is not needed.
8. The Rubber Base underlayer is best applied with a flat gel brush. Movements should be rubbing. We paint all the sinuses of the nail and dry in the lamp for 60 seconds.
9. Wipe off the stickiness.
10. Level. If leveling with gel, leave a 0.5–1 mm gap from the cuticle. Dry in the lamp for 60 seconds.
11. File the shape after leveling. This is necessary so that a thickness forms at the edge of the nail that will hold the free edge.
12. If the nail was thin, it may curl, so be sure to file 1 mm of the natural nail from the inside. In this case, there will be no material peeling. If the material is hard and the nail is very soft, the nail itself will begin to separate from the hard material from the free edge.
13. After filing, wipe off the stickiness and apply gel polish.
14. Apply top coat. Dry for 120 seconds. After drying, do not wipe with anything, as the shine may be lost.

CLASSIC EXTENSION

1. Removal
2. Shorten the nail length to 1 mm and make a round shape.
3. With a 220 grit nail file, file without strong pressure on the nail from above, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Do a manicure.
5. If working with removers, after working with them wash hands with soap.
6. Degrease the nail using Nail Prep. Do two approaches. Use 4 wipes (1 wipe per 5 fingers). First approach: wipe the surface of the nail. Second approach: take an orange stick, put a wipe on it and wipe everything in the cuticle area and sinuses.
7. Use primer
8. The Rubber Base underlayer is best applied with a flat gel brush. Movements should be rubbing. We paint all the sinuses of the nail and dry in the lamp for 60 seconds.
9. Wipe off stickiness.
10. Install the form for extending the free edge of the nail.
11. Apply clear gel to the artificial nail form. Dry for 30 seconds.
12. File the free edge and give the nail the desired shape.
13. Wipe off stickiness and excess dust.
14. Go over the areas where you used the file again with Rubber Base. Dry for 30 seconds.
15. Level with gel, put in the lamp and clamp at the 10-15th second. If the gel has strong stickiness or contains glitter, clamp at the 20th second.
16. Cure additionally in the lamp for 120 seconds.
17. Wipe off stickiness before applying gel polish.
18. Apply top coat. Dry for 120 seconds. After drying, do not wipe with anything, as the shine may be lost.

(Product photos on the website may differ from the actual product)

TPO FREE