You Are Cute. Builder Gel #36, 15 ml, builder gel for nail extensions with glitter particles

Builder Gel – a polymer light-curing material that, due to its strength, allows for significant lengthening of the nail plate. It contains photoinitiators that start the polymerization process when the material is exposed to ultraviolet light of a certain wavelength.

Features:

• Is acid-free.
• Has shock absorption; does not crack upon impact.
• Has medium consistency.
• Has medium pigmentation; covers the free edge.
• Suitable for the 'extension without filing' technique.
• Suitable for extensions 'on upper forms'.
• Does not cause a burning sensation in the lamp.
• Becomes thicker in the cold and thinner in warmth.
• Thixotropic – becomes thinner if you move the brush during application.
• It can be additionally warmed to make the gel thinner.
• Hard at a thickness of 1 mm. If the thickness is less than 1 mm, it may slightly bend, but this does not affect wear.
• Does not shrink and holds the arch well.
• Requires an underlay of Rubber Base.
• Wavelength for polymerization: 365–405 nm.
• UV/LED lamp power: 36–48W.
• Allowable coating thickness: 0.5 mm at the tip / 1 mm at the apex.
• Full polymerization: 120 seconds.

Application method: 

STRENGTHENING

1. Removal.
2. Do not file the nail shape or leave 2 mm of length to be removed after leveling.
3. Lightly file the top of the nail with a 220-grit nail file without strong pressure, lifting the scales of the nail plate, or use a 100-grit buffer.
4. Perform manicure.
5. If working with removers, wash hands with soap after use.
6. Degrease the nail using Nail Prep. Perform two passes. Use 4 wipes (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, wrap a wipe around it, and clean everything in the cuticle area and nail folds.
7. Primer is used optionally, but if the base for the underlay has sufficient acidity, it is not needed.
8. Apply the underlay with Rubber Base best using a flat gel brush. Movements should be rubbing. Draw along all nail folds and cure in the lamp for 60 seconds.
9. Remove the sticky layer.
10. Level. If leveling with gel, leave a 0.5–1 mm gap from the cuticle. Cure in the lamp for 60 seconds.
11. After leveling, file the shape. This is necessary to create thickness at the nail edge that will support the free edge.
12. If the nail was thin, it may curl, so be sure to file out 1 mm of the natural nail from the inside. In this case, there will be no material lifting. If the material is hard and the nail is very soft, the nail itself will start to separate from the hard material at the free edge.
13. After filing, remove the sticky layer and apply gel polish.
14. Apply top. Cure for 120 seconds. After curing, do not wipe with anything, as shine may be lost.

CLASSIC EXTENSIONS

1. Removal
2. Shorten the nail length to 1 mm and round the shape.
3. Lightly file the top of the nail with a 220-grit nail file without strong pressure, lifting the scales of the nail plate, or use a 100-grit buffer.
4. Perform manicure.
5. If working with removers, wash hands with soap after use.
6. Degrease the nail using Nail Prep. Perform two passes. Use 4 wipes (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, wrap a wipe around it, and clean everything in the cuticle area and nail folds.
7. Use primer
8. Apply the underlay with Rubber Base best using a flat gel brush. Movements should be rubbing. Draw along all nail folds and cure in the lamp for 60 seconds.
9. Remove the sticky layer.
10. Place the form for extending the free edge.
11. Sculpt the artificial nail shape with clear builder gel. Cure for 30 seconds.
12. File the free edge and shape the nail as desired.
13. Wipe off the sticky layer and excess dust.
14. Go over once more with Rubber Base on the areas where the nail file was used. Cure for 30 seconds.
15. Level with gel, place in the lamp, and pinch at the 10–15 second mark. If the gel has strong adhesion or contains glitter, pinch at the 20-second mark.
16. Finish curing in the lamp for 120 seconds.
17. Remove sticky layer before applying gel polish.
18. Apply top. Cure for 120 seconds. After curing, do not wipe with anything, as shine may be lost.

(Product photos on the website may differ from the actual product)

TPO FREE