You Are Cute. Builder Gel #34, 15 ml, builder gel for nail extension with glitter particles

Builder Gel – a polymer light-curing material that, thanks to its strength, allows you to significantly extend the nail plate. It contains photoinitiators that trigger the polymerization process when the material is exposed to ultraviolet light of a certain wavelength.

Features:

• It is acid-free.
• Has shock absorption, does not crack upon impact.
• Has medium consistency.
• Has medium pigmentation, covers the free edge.
• Suitable for the "no-filing extension" technique.
• Suitable for extension on top forms.
• Does not cause burning in the lamp.
• Becomes thicker in cold, thinner in heat.
• Thixotropic – becomes thinner if you move the brush during work.
• It can be additionally warmed to make the gel thinner.
• Hard at a thickness of 1 mm. If the thickness is less than 1 mm, it may bend slightly, but this does not affect wear.
• Does not shrink and holds the arch well.
• Requires a Rubber Base underlay.
• Wavelength for polymerization 365-405 nm.
• UV/LED lamp power 36-48W.
• Permissible coating thickness 0.5 mm at the end/ 1 mm at the apex.
• Full polymerization 120 seconds.

Application method:

STRENGTHENING

1. Removal.
2. Do not file the nail shape or leave 2 mm in length, which we will remove after leveling.
3. Using a 220 grit nail file, file the top of the nail without strong pressure, lifting the flakes of the nail plate, or use a 100 grit buffer.
4. Do a manicure.
5. If working with removers, wash hands with soap after using them.
6. Degrease the nail with Nail Prep. Do two passes. Use 4 wipes (1 wipe for 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, put a wipe on it, and wipe everything in the cuticle area and sidewalls.
7. Primer is optional, but if the base for underlay has sufficient acidity, it is not needed.
8. Apply the Rubber Base underlay best with a flat gel brush. Movements should be rubbing. Draw all the sidewalls of the nail and cure in the lamp for 60 seconds.
9. Wipe off the tacky layer.
10. Level. If leveling with gel, make a 0.5–1 mm indent from the cuticle. Cure in the lamp for 60 seconds.
11. File the shape after leveling. This is necessary so that the edge of the nail has a thickness that will hold the free edge.
12. If the nail was thin, it may curl, so be sure to file 1 mm of the natural nail from the inside. This will prevent material lifting. If the material is hard and the nail is very soft, the nail itself will start to separate from the hard material at the free edge.
13. After filing, wipe off the tacky layer and apply gel polish.
14. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

CLASSIC EXTENSION

1. Removal
2. Shorten the nail length to 1 mm and make a round shape.
3. Using a 220 grit nail file, file the top of the nail without strong pressure, lifting the flakes of the nail plate, or use a 100 grit buffer.
4. Do a manicure.
5. If working with removers, wash hands with soap after using them.
6. Degrease the nail with Nail Prep. Do two passes. Use 4 wipes (1 wipe for 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, put a wipe on it, and wipe everything in the cuticle area and sidewalls.
7. Use primer
8. Apply the Rubber Base underlay best with a flat gel brush. Movements should be rubbing. Draw all the sidewalls of the nail and cure in the lamp for 60 seconds.
9. Wipe off the tacky layer.
10. Install a form for extending the free edge of the nail.
11. Apply the artificial nail shape with clear gel. Cure for 30 seconds.
12. File the free edge and give the nail the desired shape.
13. Wipe off the tacky layer and excess dust.
14. Go over the areas where you used the nail file again with Rubber Base. Cure for 30 seconds.
15. Level with gel, place in the lamp, and clamp at the 10–15th second. If the gel has strong tackiness or contains glitter, clamp at the 20th second.
16. Finish curing in the lamp for 120 seconds.
17. Wipe off the tacky layer before applying gel polish.
18. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

(Product photos on the website may differ from the actual product)

TPO FREE