HEYLOVE. Tint base, NUDE, 15 ml, tinted base
Thanks to its dense pigmentation and elasticity, the NUDE tint base creates a perfectly even coating after just the first layer.
Shade: the most ideal nude
Collection: NUDE
Consistency: medium
Hardness/elasticity: elastic
Acidity: neutral, pH=6.7
Scent: neutral
Pigmentation: dense, covers the free edge
How to use:
-
Thoroughly degrease the nail plate using a dehydrator phBond.
- Apply an acid-free primer Ultrabond to the nail tip and wait until the liquid is completely dry.
-
Apply a layer of clear base Rubber base as a base coat and polymerize for 30 seconds.
-
Apply one or two layers of Tint base. Polymerization time in a UV/LED lamp is 60 seconds.
-
As the final layer, apply a top coat (top).
Volume: 15 ml
Manufacturer: TM "HEYLOVE"
Country: Ukraine
Composition (INCI): Polyacrylic Acid, HEMA, Hydroxycyclohexyl Phenyl Ketone, Ethyl Trimethylbenzoyl Phenylphosphinate, Silica. May Contain: Cl 45380, Cl 15850, Cl 77491, CI 15985, CI 77492, Cl 77007, Cl 77510, CI 77742, CI 77289, CI 77499, CI 77891, CI 7700
Attention! To avoid unwanted polymerization of the material during work, testing or content creation, keep the open bottle or brush away from daylight (especially direct sunlight). Please also note that even on cloudy days, clouds transmit a large amount of ultraviolet radiation, which is sufficient for the material to start polymerizing. When painting nail tips, we recommend keeping the working side of the UV lamp turned away from the master. If you hold the switched-on lamp with the light towards the master, unwanted polymerization of the material on brushes and necks of open bottles may occur.
Note: all documents are in the attached files!
How to prevent bubbles in the material?Bubbles can appear in any liquid. This does not depend on the formula or ingredients. It depends on density (viscosity).
This is simply a law of physics, nothing else.
For example, in water, bubbles do not last long and come out on their own.
If we take thicker liquids (honey, thick builder gel, etc.) - in these products, bubbles happily settle and do not leave them as quickly as water.
Same with base. If you work with the brush carelessly, sharply dipping it into the bottle, it involuntarily acts as a blender, mixing the material with air, creating bubbles. This is especially true for materials in bottles with a brush.
Therefore, make CAREFUL, gentle movements with the brush!
Especially when the bottle is new and full.
When we worked on developing the tint base product, we had a choice of density. We consciously chose a medium density consistency because it has advantages:
- the material does not run, does not bleed;
- contours are clear without extra effort;
- the master calmly applies the architecture and has time to check it by the glare;
- there is no need to apply a second layer to refine the architecture or camouflage the free edge.
Our production facility has equipment that prevents the formation of bubbles in the material at all stages - from pigment mixing to bottling.
We also warn our partners that we are against the store consultant opening the bottle for the client and showing the material. Because a consultant who is not a master does not understand that the brush can create bubbles even without realizing it.
Not to mention that the necks of bottles look unaesthetic when they are stained with material up to the top.
If bubbles appear in the material, how to fix it?
Unscrew the bottle cap, but do not remove the brush.
Place in a warm (but not hot!) place overnight.
Or put the bottle in a plastic bag and immerse it in warm water (up to the neck).
According to the laws of physics, in a warm environment molecules move faster, and this speeds up the process.
The air will rise to the surface, it is lighter than the liquid.
- Ukraine
- Opaque
- Нюдовые/бежевые/коричневые