HEYLOVE. Tint base, LOTUS, 15 ml, tint base
Thanks to its dense pigmentation and elasticity, the LOTUS tinted base creates a perfectly even coverage after the first layer.
Shade: bright pink
Collection: AWAKING
Consistency: medium
Stiffness/elasticity: elastic
Acidity: neutral, pH=6.7
Odor: neutral
Pigmentation: dense, covers the free edge
How to use:
-
Thoroughly degrease the nail plate using a dehydrator phBond.
- Apply an acid-free primer Ultrabond to the tip of the nail and wait for the liquid to dry completely.
-
Apply a layer of clear base Rubber base as an undercoat and cure for 30 seconds.
-
Apply one or two layers of Tint base. Cure time in UV/LED lamp: 60 seconds.
-
As the last layer, apply a finish coating (top).
Volume: 15 ml
Manufacturer: TM "HEYLOVE"
Country: Ukraine
Ingredients (INCI): Polyacrylic Acid, HEMA, Hydroxycyclohexyl Phenyl Ketone, Ethyl Trimethylbenzoyl Phenylphosphinate, Silica. May Contain: Cl 45380, Cl 15850, Cl 77491, CI 15985, CI 77492, Cl 77007, Cl 77510, CI 77742, CI 77289, CI 77499, CI 77891, CI 7700
Attention! To avoid unwanted polymerization of the material during work, testing, or content shooting, the opened bottle or brush should be kept as far away from daylight (especially direct sunlight) as possible. We also ask you to note that even in cloudy weather, clouds transmit a large amount of ultraviolet radiation, which is sufficient for the material to start polymerizing. When painting nail tips, we recommend keeping the working side of the operating UV lamp away from the master. If the lamp is held with the light towards the master, unwanted polymerization of the material on the brushes and the necks of open bottles may occur.
Note: all documents are in the attached files!
How to prevent bubbles in the material?Bubbles can appear in any liquid. It does not depend on the formula or ingredients. It depends on the density (viscosity).
It's just a law of physics, nothing else.
For example, in water, bubbles last very briefly and come out on their own.
If we take thicker liquids (honey, thick builder gel for extensions, etc.) - in these products, bubbles readily settle and do not leave them as quickly as water.
The same goes for the base. If you work carelessly with the brush, sharply dipping it into the bottle, it involuntarily acts like a blender, mixing the material with air and creating bubbles. This is especially true for materials in bottles with a brush.
Therefore, we make CAREFUL, gentle movements with the brush!
Especially when the bottle is new and full.
When we were working on the development of the tint base product, we faced a choice of thickness. We deliberately chose a medium thickness consistency because it has advantages:
- the material does not run, does not flood;
- contours are clear without extra effort;
- the master calmly builds the architecture and has time to check it by the highlight;
- there is no need to apply a second layer to refine the architecture or camouflage the free edge.
Our production has equipment that prevents the formation of bubbles in the material at all stages – from pigment mixing to bottling.
We also warn our partners that we are against a store consultant opening the bottle for a customer and showing the material. Because a consultant who is not a master does not understand that you can create bubbles with the brush without even realizing it.
Not to mention the fact that the necks of the bottles look unsightly when they are contaminated with material to the very top.
If bubbles appear in the material, how to fix it?
Unscrew the bottle cap, but do not pull out the brush.
Put it in a warm (but not hot!) place overnight.
Or put the bottle in a plastic bag and immerse it in warm water (up to the shoulders).
According to the law of physics, in a warm environment, molecules move faster, and this speeds up the process.
The air will come to the surface, it is lighter than liquid.
- Opaque
- Ukraine
- Розовые