HEYLOVE. Tint base, JELLY BELLY, 15 ml, tinted base with shimmer
Thanks to its dense pigmentation and elasticity, the JELLY BELLY tinted base creates a perfectly even coating after the first layer.
Shade: pink-peach
Collection: POP DRINKS
Consistency: medium
Hardness/elasticity: elastic
Acidity: neutral, pH=6.7
Odor: neutral
Pigmentation: dense, covers the free edge
How to use:
-
Thoroughly degrease the nail plate using pH Bond dehydrator.
- Apply an acid-free primer Ultrabond to the tip of the nail and wait for the liquid to dry completely.
-
Apply a layer of transparent Rubber base as a base coat and cure for 30 seconds.
-
Apply one or two layers of Tint base. Cure in a UV/LED lamp for 60 seconds.
-
Last layer apply a finishing coat (top).
Volume: 15 ml
Manufacturer: TM "HEYLOVE"
Country: Ukraine
Composition (INCI): Polyacrylic Acid, HEMA, Hydroxycyclohexyl Phenyl Ketone, Ethyl Trimethylbenzoyl Phenylphosphinate, Silica.
May Contain: CI 45380, CI 15850, CI 77491,CI 15985,CI 77492, CI77007, CI 77510, CI 77742, CI 77289, CI 77499, CI 77891, CI 77000
Caution! To avoid unwanted polymerization of the material during work, testing, or content shooting, keep the open bottle or brush as far away from daylight as possible (especially direct sunlight). Please also note that even on a cloudy day, clouds transmit a large amount of ultraviolet radiation, which is sufficient for the material to start polymerizing. When painting nail tips, we recommend keeping the working side of the UV lamp that is on, facing away from the technician. Holding the switched-on lamp with the light towards the technician can cause unwanted polymerization of the material on the brushes and on the necks of open bottles.
Note: all documents are in the attached files!
How to prevent bubbles in the material?Bubbles can appear in any liquid. It does not depend on the formula or ingredients. It depends on the thickness (viscosity).
It's simply a law of physics, nothing else.
For example, bubbles in water stay for a very short time and come out on their own.
If we take thicker liquids (honey, thick builder gel, etc.) - bubbles readily settle in these products and do not leave them as quickly as water.
Same with base. If you work with the brush carelessly, steeply dipping it into the bottle, it involuntarily acts as a blender, mixing the material with air, forming bubbles. This especially applies to materials in bottles with a brush.
Therefore, make CAREFUL, gentle movements with the brush!
Especially when the bottle is new and full.
When we were developing the tint base product, we had a choice of consistency. We deliberately chose a medium consistency because it has advantages:
- the material does not run anywhere, does not flood;
- contours are clear without extra effort;
- the technician calmly builds the architecture and has time to check it by the highlight;
- there is no need to apply a second layer to refine the architecture or camouflage the free edge.
Our production has equipment that prevents the formation of bubbles in the material at all stages – from mixing the pigment to filling into bottles.
We also warn our partners that we are against a store consultant opening the bottle for the client and showing the material. Because a consultant who is not a technician does not understand that bubbles can be created with the brush, even unconsciously.
Not to mention that bottle necks look unsightly when they are soiled with material to the top.
If bubbles have appeared in the material, how to fix it?
Unscrew the cap of the bottle, but do not remove the brush.
Place it in a warm (but not hot!) place for the night.
Or put the bottle in a plastic bag and immerse it in warm water (up to the shoulders).
According to the law of physics, in a warm environment, molecules move faster, and this speeds up the process.
Air will come to the surface, it is lighter than liquid.
- Opaque
- С блестящими частицами/поталью
- Ukraine
- Розовые