HEYLOVE. Tint base, MORSE, 15 ml, tint base with shimmer
Thanks to its dense pigmentation and elasticity, MORSE tint base creates a perfectly even coating after just the first layer.
Shade: cool pink
Collection: POP DRINKS
Consistency: medium
Hardness/elasticity: elastic
Acidity: neutral, pH=6.7
Odor: neutral
Pigmentation: dense, covers the free edge
Application method:
-
Thoroughly degrease the nail plate using dehydrator phBond.
- Apply acid-free primer to the tip of the nail Ultrabond and wait for it to dry completely.
-
Apply a layer of clear base Rubber base as a base and cure for 30 seconds.
-
Apply one or two layers of Tint base. Curing time in UV/LED lamp: 60 seconds.
-
Finally, apply a finish coating (top).
Volume: 15 ml
Manufacturer: TM "HEYLOVE"
Country: Ukraine
Ingredients (INCI): Polyacrylic Acid, HEMA, Hydroxycyclohexyl Phenyl Ketone, Ethyl Trimethylbenzoyl Phenylphosphinate, Silica.
May Contain: CI 45380, CI 15850, CI 77491,CI 15985,CI 77492, CI77007, CI 77510, CI 77742, CI 77289, CI 77499, CI 77891, CI 77000
Warning! To avoid unwanted polymerization of the material during work, testing, or content creation, keep the open bottle or brush as far away from daylight (especially direct sunlight) as possible. Also, please note that even in cloudy weather, clouds transmit a large amount of ultraviolet radiation sufficient to cause the material to start polymerizing. When staining tips, we recommend keeping the working side of the UV lamp facing away from the master. If you hold the turned-on lamp facing the master, unwanted polymerization of the material on brushes and necks of open bottles may occur.
Note: all documents are in the attached files!
How to prevent bubbles in the material?Bubbles can appear in any liquid. This does not depend on the formula or ingredients. It depends on density (viscosity).
It's just a law of physics, nothing else.
For example, in water, bubbles last very briefly and escape on their own.
If we take thicker liquids (honey, thick builder gel, etc.) - in these products bubbles settle readily and do not leave as quickly as water.
The same goes for base. If you work carelessly with the brush, plunging it sharply into the bottle, it inadvertently acts like a blender, mixing the material with air, creating bubbles. This is especially true for materials in bottles with a brush.
Therefore, make GENTLE, soft brush movements!
Especially when the bottle is new and full.
When we were developing the tint base product, we had a choice of density. We deliberately chose a medium density consistency because it has advantages:
- the material does not run or seep;
- clear contours without extra effort;
- the master calmly applies the architecture and has time to check it by the shine;
- there is no need to apply a second layer to refine the architecture or camouflage the free edge.
Our production facility has equipment that prevents bubble formation in the material at all stages – from pigment mixing to filling into bottles.
We also warn our partners that we are against the consultant in the store opening the bottle for the client and showing the material. Because a consultant who is not a master does not understand that the brush can create bubbles without even realizing it.
Not to mention that the necks of bottles look unsightly when soiled with material all the way to the top.
If bubbles have appeared in the material, how to fix it?
Unscrew the bottle cap, but do not remove the brush.
Place in a warm (but not hot!) place overnight.
Or put the bottle in a plastic bag and immerse in warm water (up to the shoulders).
According to the laws of physics, in a warm environment molecules move faster, which accelerates the process.
The air will rise to the surface—it is lighter than the liquid.
- Opaque
- С блестящими частицами/поталью
- Ukraine
- Розовые