HEYLOVE. Tint base, MATCHA, 15 ml, tint base
Thanks to its dense pigmentation and elasticity, MATCHA tint base creates a perfectly even coating after the first application.
Shade: dusted mint
Collection: LIFESTYLE
Collection overview at: https://www.instagram.com/reel/DEziujPItnV/?igsh=YTJ4cWlxeDcxbHQ1
Consistency: medium
Hardness/elasticity: elastic
Acidity: neutral, pH=6.7
Smell: neutral
Pigmentation: dense, covers the free edge
Application method:
-
Thoroughly degrease the nail plate using the dehydrator phBond.
- Apply acid-free primer Ultrabond to the tip of the nail and wait for complete drying.
-
Apply a layer of clear base Rubber base as a base coat and cure for 30 seconds.
-
Apply one or two layers of Tint base. Curing time in UV/LED lamp is 60 seconds.
-
Finally, apply a top coat.
Volume: 15 ml
Manufacturer: TM "HEYLOVE"
Country: Ukraine
Composition (INCI): Polyacrylic Acid, HEMA, Hydroxycyclohexyl Phenyl Ketone, Ethyl Trimethylbenzoyl Phenylphosphinate, Silica. May Contain: Cl 45380, Cl 15850, Cl 77491, CI 15985, CI 77492, Cl 77007, Cl 77510, CI 77742, CI 77289, CI 77499, CI 77891, CI 7700
Attention! To avoid unwanted polymerization of the material during work, testing, or content creation, keep the open bottle or brush as far away from daylight (especially direct sunlight) as possible. Please also note that even in cloudy weather, clouds transmit a large amount of ultraviolet radiation, enough to cause the material to begin polymerizing. When painting tips, we recommend holding the working side of the UV lamp away from the master. If you hold the turned-on lamp with light towards the master, unwanted polymerization of the material on brushes and necks of open bottles may occur.
Note: all documents are in the attached files!
How to prevent bubbles in the material?Bubbles can appear in any liquid. This does not depend on the formula or components. It depends on the density (viscosity).
It's just a law of physics, nothing else.
For example, in water, bubbles last very short and come out on their own.
If we take thicker liquids (honey, thick builder gel, etc.) - in these products, bubbles settle eagerly and do not leave them as quickly as water.
Same with base. If you work with the brush carelessly, sharply dipping it into the bottle, it involuntarily acts like a blender, mixing the material with air, forming bubbles. This especially applies to materials in bottles with a brush.
Therefore, make CAREFUL, gentle movements with the brush!
Especially when the bottle is new and full.
When we developed the tint base product, we had a choice of density. We deliberately chose a medium consistency, because it has advantages:
- the material does not run anywhere, does not seep;
- contours are clear without extra effort;
- the master calmly builds architecture and has time to check it by the gloss;
- there is no need to apply a second layer to refine the architecture or camouflage the free edge.
Our factory has equipment that prevents the formation of bubbles in the material at all stages - from mixing the pigment to bottling.
We also warn our partners that we are against the store consultant opening the bottle for the client and showing the material. Because a consultant who is not a master does not understand that a brush can create bubbles without even realizing it.
Not to mention that the necks of the bottles look unsightly when they are smeared with material to the very top.
If bubbles appear in the material, how to fix it?
Unscrew the bottle cap, but do not remove the brush.
Place in a warm (but not hot!) place overnight.
Or put the bottle in a plastic bag and soak in warm water (up to the neck).
According to the law of physics, in a warm environment, molecules move faster, and this speeds up the process.
The air will come to the surface, it is lighter than the liquid.
- Ukraine
- Opaque
- Зелёные/салатовые