You Are Cute. Builder Gel #12, 15 ml, builder gel

Builder Gel is a polymer light-curing material that, due to its strength, allows significant lengthening of the nail plate. It contains photoinitiators that trigger the polymerization process when the material is exposed to ultraviolet light of a specific wavelength.

Features:

• It is acid-free.
• Has shock absorption, does not crack upon impact.
• Has medium consistency.
• Has medium pigmentation, covers the free edge.
• Suitable for the "extension without filing" technique.
• Suitable for extension "on upper forms".
• Does not cause burning in the lamp.
• In cold it becomes thicker, in warmth — thinner.
• Thixotropic — becomes thinner if you move the brush while working.
• It can be additionally warmed up to make the gel thinner.
• Hard at a thickness of 1 mm. If the thickness is less than 1 mm, it may bend slightly, but this does not affect wear.
• Does not shrink and holds the arch well.
• Requires a Rubber Base underlayment.
• Polymerization wavelength 365-405 nm.
• UV/LED lamp power 36-48W.
• Allowable coating thickness 0.5 mm at the tip / 1 mm at the apex.
• Full polymerization 120 seconds.

Application method:

STRENGTHENING

1. Removal.
2. Do not file the nail shape or leave 2 mm in length, which we will remove after leveling.
3. With a 220-grit nail file, file without strong pressure on top of the nail, lifting the scales of the nail plate, or use a 100-grit buffer.
4. Perform a manicure.
5. If working with removers, after working with them, wash hands with soap.
6. Degrease the nail with Nail Prep. Do two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the surface of the nail. Second pass: take an orange stick, put a wipe on it, and wipe everything in the cuticle area and sidewalls.
7. Use primer optionally, but if the base for the underlayment has sufficient acidity, it is not needed.
8. The Rubber Base underlayment is best applied with a flat gel brush. Movements should be rubbing. Draw out all the sidewalls of the nail and cure in the lamp for 60 seconds.
9. Wipe off the tacky layer.
10. Level. If leveling with builder gel, make a setback from the cuticle of 0.5–1 mm. Cure in the lamp for 60 seconds.
11. File the shape after leveling. This is necessary to create a thickness at the edge of the nail that will hold the free edge.
12. If the nail was thin, it may curl, so be sure to file out 1 mm of the natural nail from the inside. In this case, there will be no material lifting. If the material is hard and the nail is very soft, the nail itself will start to separate from the hard material at the free edge.
13. After filing, wipe off the tacky layer and apply gel polish.
14. Apply top. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

CLASSIC EXTENSION

1. Removal
2. Shorten the nail length to 1 mm and create a round shape.
3. With a 220-grit nail file, file without strong pressure on top of the nail, lifting the scales of the nail plate, or use a 100-grit buffer.
4. Perform a manicure.
5. If working with removers, after working with them, wash hands with soap.
6. Degrease the nail with Nail Prep. Do two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the surface of the nail. Second pass: take an orange stick, put a wipe on it, and wipe everything in the cuticle area and sidewalls.
7. Use primer
8. The Rubber Base underlayment is best applied with a flat gel brush. Movements should be rubbing. Draw out all the sidewalls of the nail and cure in the lamp for 60 seconds.
9. Wipe off the tacky layer.
10. Place the form for extending the free edge of the nail.
11. Build the artificial nail shape with clear builder gel. Cure for 30 seconds.
12. File the free edge and shape the nail as desired.
13. Wipe off the tacky layer and excess dust.
14. Go over again with Rubber Base on the areas where the file was used. Cure for 30 seconds.
15. Level with builder gel, place in the lamp and at the 10–15 seconds pinch. If the gel has strong tack or contains glitter, pinch at 20 seconds.
16. Finish curing in the lamp for 120 seconds.
17. Wipe off the tacky layer before applying gel polish.
18. Apply top. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

(Product photo on the website may differ from the actual product)

TPO FREE