You Are Cute. Builder Gel #10, 15 ml, builder gel

Builder Gel – a polymer light-curing material that, due to its strength, allows significant lengthening of the nail plate. It contains photoinitiators that trigger the polymerization process when the material is exposed to ultraviolet light of a certain wavelength.

Features:

• It is acid-free.
• It has shock absorption, does not crack upon impact.
• It has a medium consistency.
• It has medium pigmentation, covers the free edge.
• Suitable for the "extension without filing" technique.
• Suitable for extension on upper forms.
• Does not cause a burning sensation in the lamp.
• Becomes thicker in the cold and thinner in warmth.
• Thixotropic – becomes thinner when moving the brush during application.
• It can be additionally warmed to make the gel thinner.
• Hard at a thickness of 1 mm. If the thickness is less than 1 mm, it may flex slightly, but this does not affect wear.
• Does not shrink and holds the arch well.
• Requires a base layer of Rubber Base.
• Wavelength for polymerization: 365-405 nm.
• UV/LED lamp power: 36-48W.
• Allowable coating thickness: 0.5 mm at the free edge / 1 mm at the apex.
• Full polymerization: 120 seconds.

Application Method:

STRENGTHENING

1. Removal.
2. Do not file the nail shape or leave 2 mm in length, which will be removed after leveling.
3. With a 220-grit nail file, file without strong pressure on the nail from above, lifting the nail plate scales, or use a 100-grit buffer.
4. Perform a manicure.
5. If working with removers, after using them wash hands with soap.
6. Degrease the nail using Nail Prep. Do two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, wrap a wipe around it, and wipe everything in the cuticle area and nail folds.
7. Use primer as desired, but if the base for the underlay has sufficient acidity, it is not needed.
8. Apply the Rubber Base underlay best with a flat gel brush. Movements should be rubbing. Draw through all nail folds and cure in the lamp for 60 seconds.
9. Remove the tacky layer.
10. Level. If leveling with builder gel, leave a gap of 0.5–1 mm from the cuticle. Cure in the lamp for 60 seconds.
11. File the shape after leveling. This is necessary to create thickness at the nail edge that will hold the free edge.
12. If the nail was thin, it may curl, so be sure to file 1 mm of the natural nail from the inside. In this case, there will be no material delamination. If the material is hard and the nail is very soft, the nail itself will start to separate from the hard material from the free edge.
13. After filing, remove the tacky layer and apply gel polish.
14. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

CLASSIC EXTENSION

1. Removal
2. Shorten the nail length to 1 mm and create a round shape.
3. With a 220-grit nail file, file without strong pressure on the nail from above, lifting the nail plate scales, or use a 100-grit buffer.
4. Perform a manicure.
5. If working with removers, after using them wash hands with soap.
6. Degrease the nail using Nail Prep. Do two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, wrap a wipe around it, and wipe everything in the cuticle area and nail folds.
7. Use primer
8. Apply the Rubber Base underlay best with a flat gel brush. Movements should be rubbing. Draw through all nail folds and cure in the lamp for 60 seconds.
9. Remove the tacky layer.
10. Place a form for extending the free edge of the nail.
11. Sculpt the artificial nail shape with clear builder gel. Cure for 30 seconds.
12. File the free edge and shape the nail as desired.
13. Remove the tacky layer and excess dust.
14. Go over again with Rubber Base on the areas where the nail file was used. Cure for 30 seconds.
15. Level with builder gel, place in the lamp and pinch at 10-15 seconds. If the gel has strong tackiness or contains glitter, pinch at 20 seconds.
16. Final cure in the lamp for 120 seconds.
17. Remove the tacky layer before applying gel polish.
18. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

(Product photos on the website may differ from the actual product)

TPO FREE