You Are Cute. Builder Gel #01, 15 ml, builder gel

Builder Gel – polymer light-curing material, which due to its strength allows significantly lengthening the nail plate. It contains photoinitiators that start the polymerization process when the material is exposed to ultraviolet light of a certain wavelength.

Features:

• Is acid-free.
• Has shock absorption, does not crack upon impact.
• Has a medium consistency.
• Has medium pigmentation, covers the free edge.
• Suitable for the technique of 'extension without filing'.
• Suitable for extension 'on upper forms'.
• Does not cause burning in the lamp.
• Becomes thicker in the cold, and thinner in warmth.
• Thixotropic — becomes thinner if you move the brush during work.
• It can be additionally warmed to make the gel thinner.
• Hard at a thickness of 1 mm. If the thickness is less than 1 mm, it may bend slightly, but this does not affect wear.
• Does not shrink and holds the arch well.
• Definitely requires a Rubber Base underlay.
• Wavelength for polymerization 365-405 nm.
• UV/Led lamp power 36-48W.
• Permissible coating thickness 0.5 mm at the tip / 1 mm at the apex.
• Full polymerization 120 seconds.

Application method: 

STRENGTHENING

1. Removal.
2. Do not file the nail shape or leave 2 mm in length, which we will remove after leveling.
3. With a 220 grit nail file, file without strong pressure on the nail from above, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Do a manicure.
5. If working with removers, after using them, wash hands with soap.
6. Degrease the nail with Nail Prep. Make two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, place a wipe on it and wipe everything in the cuticle area and sidewalls.
7. Primer is used optionally, but if the base for the underlay has sufficient acidity, then it is not needed.
8. Rubber Base underlay is best applied with a flat gel brush. Movements should be rubbing. Draw through all nail sidewalls and cure in a lamp for 60 seconds.
9. Wipe off the inhibition layer.
10. Level. If leveling with gel, make an indent from the cuticle of 0.5–1 mm. Cure in a lamp for 60 seconds.
11. File the shape after leveling. This is necessary to create thickness at the nail edge that will hold the free edge.
12. If the nail was thin, it may curl, so be sure to file out 1 mm of the natural nail from the inside. In this case, there will be no material lifting. If the material is hard and the nail is very soft, the nail itself will start to separate from the hard material from the free edge.
13. After filing, wipe off the inhibition layer and apply gel polish.
14. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

CLASSIC EXTENSION

1. Removal
2. Shorten the nail length to 1 mm and make a round shape.
3. With a 220 grit nail file, file without strong pressure on the nail from above, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Do a manicure.
5. If working with removers, after using them, wash hands with soap.
6. Degrease the nail with Nail Prep. Make two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, place a wipe on it and wipe everything in the cuticle area and sidewalls.
7. Use primer
8. Rubber Base underlay is best applied with a flat gel brush. Movements should be rubbing. Draw through all nail sidewalls and cure in a lamp for 60 seconds.
9. Wipe off the inhibition layer.
10. Place the form for extending the free edge of the nail.
11. Lay out the artificial nail shape with clear gel. Cure for 30 seconds.
12. File the free edge and give the nail the desired shape.
13. Wipe off the inhibition layer and excess dust.
14. Go over again with Rubber Base on the areas where the file was used. Cure for 30 seconds.
15. Level with gel, place in the lamp and pinch at the 10–15-second mark. If the gel has strong adhesion or contains glitter, pinch at the 20-second mark.
16. Cure fully in the lamp for 120 seconds.
17. Wipe off the inhibition layer before applying gel polish.
18. Apply top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

(Product photos on the website may differ from the actual product)

TPO FREE