HEYLOVE. Tint base, BRIDE, 15 ml, tinted base
Descrição
Due to its dense pigmentation and elasticity, the tint base BRIDE creates a perfectly even coating after just one coat. Does not change color after polymerization.
Shade: milky white
Collection: NUDE
Consistency: medium
Hardness/flexibility: flexible
Acidity: neutral, pH=6.7
Scent: neutral
Pigmentation: dense, covers the free edge
How to use:
-
Thoroughly degrease the nail plate using a dehydrator phBond.
- Apply an acid-free primer to the tip of the nail Ultrabond and wait for the liquid to dry completely.
-
Apply a layer of clear base coat Rubber base as a base and polymerize for 30 seconds.
-
Apply one or two coats of Tint base. Polymerization time in a UV/LED lamp is 60 seconds.
-
Finally apply with a ball finish coating (top).
Volume: 15 ml
Manufacturer: TM "HEYLOVE"
Country: Ukraine
Ingredients (INCI): Polyacrylic Acid, HEMA, Hydroxycyclohexyl Phenyl Ketone, Ethyl Trimethylbenzoyl Phenylphosphinate, Silica. May Contain: Cl 45380, Cl 15850, Cl 77491, CI 15985, CI 77492, Cl 77007, Cl 77510, CI 77742, CI 77289, CI 77499, CI 77891, CI 7700
Caution! To avoid unwanted polymerization of the material during work, testing or content shooting, keep the open bottle or brush as far away from daylight (especially direct sunlight). Also please note that even in cloudy weather clouds transmit a large amount of ultraviolet radiation sufficient to start the material to polymerize. When painting tips, we recommend keeping the working side of the UV lamp that is on facing away from the master. If you keep the lamp on facing the master, unwanted polymerization may occur on the brushes and necks of open bottles.
Note: all documents are in the attached files!
How to prevent bubbles in the material?Bubbles can appear in any liquid. This does not depend on the formula or ingredients. This depends on density (viscosity).
It's just a law of physics, nothing else.
For example, in water bubbles last very shortly and exit on their own.
If we take thicker liquids (honey, thick gel for extension, etc.) - in these products bubbles readily settle and do not leave them as quickly as water.
The same with the base. If the brush works carelessly, sharply dipping it into the bottle, involuntarily it acts as a blender, mixing the material with air, forming bubbles. This is especially the case for materials in bottles with a brush.
Therefore, we make CAREFUL, gentle movements with the brush!
Especially when the bottle is new and full.
When we worked on the development of the tint base product, we had a choice of density. We deliberately chose a medium-thick consistency because there are advantages:
- material does not run anywhere, does not flow into;
- contours are clear without extra effort;
- the master calmly applies the architecture and has time to check it by the glare;
- there is no need to apply a second layer to refine the architecture or camouflage the free edge.
At our production facility, we have equipment that prevents the formation of bubbles in the material at all stages – from pigment mixing to bottling.
We also warn our partners that we are against a store consultant opening a bottle for a client and showing the material. Because a consultant who is not a master does not understand that the brush can create bubbles even without realizing it.
Not to mention that the necks of bottles look unaesthetic when they are soiled with material all the way to the top.
If bubbles appear in the material, how to fix this?
Unscrew the cap of the bottle, but do not pull out the brush.
Place in a warm (but not hot!) place overnight.
Or put the bottle in a plastic bag and immerse it in warm water (up to the shoulders).
According to the laws of physics, in a warm environment molecules move faster, and this accelerates the process.
The air will rise to the surface; it is lighter than the liquid.