DISCOUNT / HEYLOVE. Tint base, KOMBUCHA, 15 ml, tinted base with shimmer

ATTENTION! The bottle has minor damage. This does not affect the product's properties in any way.

Thanks to its dense pigmentation and elasticity, the KOMBUCHA tinted base creates a perfectly even coating after just the first layer.

Shade: pink-beige

Collection: POP DRINKS

Consistency: medium

Hardness/Elasticity: elastic

Acidity: neutral, pH=6.7

Scent: neutral

Pigmentation: dense, covers the free edge

How to use:

• Thoroughly degrease the nail plate using a dehydrator phBond.
• Apply an acid-free primer to the nail tip Ultrabond and wait for the liquid to dry completely.
• Apply a layer of clear base Rubber base as a base coat and cure for 30 seconds.
• Apply one or two layers of Tint base. Curing time in UV/LED lamp: 60 seconds.
• As a finishing layer, apply top coat (top).

Volume: 15 ml

Manufacturer: TM "HELLO. by NAILSMADE"

Country: Ukraine

Ingredients: Polyacrylic Acid, HEMA, Hydroxycyclohexyl Phenyl Ketone, Trimethylbenzoy Diphenylphosphine Oxide, Silica.

• May contain: CI 45380, CI 15850, CI 77491,CI 15985,CI 77492, CI77007, CI 77510, CI 77742, CI 77289, CI 77499, CI 77891, CI 77000,CI 77820.

Attention! To avoid unwanted polymerization of the material during work, testing, or content shooting, keep the open bottle or brush as far away from daylight as possible (especially direct sunlight). Please also note that even in cloudy weather, clouds transmit a large amount of ultraviolet radiation, which is sufficient for the material to start polymerizing. When painting tips, we recommend keeping the working side of the UV lamp turned away from the master. If you keep the lamp on with the light facing the master, unwanted polymerization of the material on the brushes and necks of open bottles may occur.

Note: all documents are in the attached files!

How to prevent bubbles in the material?

Bubbles can appear in any liquid. This does not depend on the formula or ingredients. It depends on the density (viscosity).
It's simply a law of physics, nothing else.

For example, in water, bubbles last very briefly and escape on their own.
If we take thicker liquids (honey, thick builder gel, etc.) - in these products, bubbles settle in willingly and do not leave them as quickly as water.

The same goes for the base. If you work carelessly with the brush, sharply dipping it into the bottle, it involuntarily acts as a blender, mixing the material with air, creating bubbles. This is especially true for materials in bottles with a brush.

Therefore, make CAREFUL, gentle movements with the brush!
Especially when the bottle is new and full.

When we were developing the tint base product, we had a choice of density. We consciously chose a medium density consistency because it has advantages:
- the material does not run or seep;
- clear contours without extra effort;
- the master can calmly build the architecture and has time to check it by the gloss;
- no need to apply a second layer to refine the architecture or camouflage the free edge.

At our production facility, we have equipment that prevents the formation of bubbles in the material at all stages – from mixing the pigment to bottling.

We also warn our partners that we are against a store consultant opening a bottle for a client to show the material. Because a consultant who is not a master does not understand that the brush can create bubbles without even realizing it.
Not to mention that the necks of the bottles look unaesthetic when they are stained with material all the way to the top.

If bubbles appear in the material, how to fix it?

Unscrew the bottle cap, but do not remove the brush.
Place it in a warm (but not hot!) place overnight.
Or put the bottle in a plastic bag and submerge it in warm water (up to the shoulders).

By the law of physics, in a warm environment, molecules move faster, and this speeds up the process.
The air will rise to the surface; it is lighter than the liquid.

Tint base by HELLO.