You Are Cute. Bottle Gel #26, 15 ml, liquid translucent gel

LIQUID GEL BOTTLE GEL — an innovative material for strengthening, leveling, and extending nails. It is a symbiosis of polygel and base. It consists of 60–80% acrylic copolymer (the main component of polygel) and a small amount of hydroxyethyl methacrylate HEMA (approximately 20–30%), the main component of base coatings. This gel can completely replace the base.

Features:

• Wavelength for polymerization — 365–405 nm.
• UV/LED lamp power — 36–48 W.
• Allowable coating thickness — 0.5 mm at the nail edge, 1 mm at the apex.
• Acid-free, medium consistency.
• Medium pigmentation, covers the free edge.
• Full polymerization occurs in 120 seconds.
• Suitable only for nail strengthening and extension.
• Good cushioning.
• When strengthening with this gel, the natural nail must be filed.
• Requires a base coat of Rubber Base.
• It can be additionally heated to make the gel thinner.

Application method:

STRENGTHENING:

1. Removal.
2. Do not file the nail shape or leave 2 mm in length, which will be removed after leveling.
3. File with a 220 grit file without strong pressure on the nail from above, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Perform a manicure.
5. If working with removers, wash hands with soap after working with them.
6. Degrease the nail using Nail Prep. Do two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, put a wipe on it, and wipe everything in the cuticle area and sinuses.
7. Use primer optionally, but if the base for the base coat has sufficient acidity, it is not needed.
8. It is best to apply the base coat of Rubber Base with a flat gel brush. Movements should be rubbing. Paint all the sinuses of the nail and cure in the lamp for 60 seconds.
9. Wipe off the stickiness.
10. Level. If leveling with gel, make an indent of 0.5–1 mm from the cuticle. Cure in the lamp for 60 seconds.
11. File the shape after leveling. This is necessary so that a thickness forms at the edge of the nail that will hold the free edge.
12. If the nail was thin, it may curl, so be sure to file 1 mm of the natural nail from the inside. In this case, there will be no material lifting. If the material is hard and the nail is very soft, the nail itself will begin to separate from the hard material from the free edge.
13. After filing, wipe off the stickiness and cover with gel polish.
14. Cover with top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

CLASSIC EXTENSION:

1. Removal
2. Shorten the nail length to 1 mm and make a round shape.
3. File with a 220 grit file without strong pressure on the nail from above, lifting the scales of the nail plate, or use a 100 grit buffer.
4. Perform a manicure.
5. If working with removers, wash hands with soap after working with them.
6. Degrease the nail using Nail Prep. Do two passes. Use 4 wipes for this (1 wipe per 5 fingers). First pass: wipe the nail surface. Second pass: take an orange stick, put a wipe on it, and wipe everything in the cuticle area and sinuses.
7. Use primer.
8. It is best to apply the base coat of Rubber Base with a flat gel brush. Movements should be rubbing. Paint all the sinuses of the nail and cure in the lamp for 60 seconds.
9. Wipe off the stickiness.
10. Set the form for extending the free edge of the nail.
11. Lay out the shape of the artificial nail with transparent gel. Cure for 30 seconds.
12. File the free edge and give the nail the desired shape.
13. Wipe off the stickiness and excess dust.
14. Go over again with Rubber Base on the areas where the file was used. Cure for 30 seconds.
15. Level with gel, place in the lamp and clamp at the 10–15th second. If the gel has strong stickiness or contains glitter, clamp at the 20th second.
16. Finish curing in the lamp for 120 seconds.
17. Wipe off the stickiness before applying gel polish.
18. Cover with top coat. Cure for 120 seconds. After curing, do not wipe with anything, as the shine may be lost.

TPO FREE